Agricultural vehicles — Standardized access to repair and maintenance information (RMI) — Part 2: Ve...
This document specifies the access to vehicle on-board diagnostics (OBD) by describing minimum hardware and software requirements including requirements for reprogramming, calibration and configuration after repair works. In addition, it provides hardware and software specifications for diagnostic tools.
This document does not apply to retrofit kits as these kits are not an integrated part of the…
Textiles — Unevenness of textile strands — Capacitance method
This document describes a method, using capacitance measuring equipment, for determining the unevenness of linear density along the length of textile strands.
The method is applicable to tops, slivers, rovings, spun yarns and continuous filament yarns, made from either natural or man-made fibres, in the range of 4 tex (g/km) to 80 ktex (kg/km) for staple-fibre strands and 1 tex(g/km) to 600 tex (…
Acoustics — Measurement of the influence of road surfaces on traffic noise — Part 3: Reference tyres
This document specifies two tyres intended to serve as reference tyres when using the close-proximity (CPX) method specified in ISO 11819-2.
The CPX method is a method for evaluating different road surfaces with respect to their influence on traffic noise, under conditions when tyre/road noise dominates. This method ideally requires the use of standardized tyres, which have noise characteristics…
Piezoelectric, dielectric and electrostatic devices and associated materials for frequency control, ...
IEC TS 61994-3:2021(E) gives the terms and definitions for piezoelectric, dielectric and electrostatic oscillators representing the state of the art, which are intended for use in the standards and documents of IEC TC 49.
The main changes with respect to the previous edition are as listed below:
- some definitions have been updated;
- the terminology given in IEC 60679-1:2017 has been taken…
Automatic electrical controls - Part 2-5: Particular requirements for automatic electrical burner co...
IEC 60730-2-5:2013+A1:2017+A2:2021 applies to automatic electrical burner control systems for the automatic control of burners for oil, gas, coal or other combustibles for household and similar use including heating, air conditioning and similar use. This part 2-5 is applicable to a complete burner control system and to a separate programming unit. This part 2-5 is also applicable to a separate…
Water quality — Determination of cyclic volatile methylsiloxanes in water — Part 2: Method using liq...
This document specifies a method for the determination of certain cyclic volatile methylsiloxanes (cVMS) in environmental water samples with low density polyethylene (LDPE) as a preservative and subsequent liquid-liquid extraction with hexane containing 13C-labeled cVMS as internal standards. The extract is then analysed by gas chromatography-mass spectrometry (GC-MS).
NOTE Using the 13C-…
Privacy protection - Privacy guidelines for smart cities
The document takes a multiple agency as well as a citizen-centric viewpoint.
It provides guidance on:
— smart city ecosystem privacy protection;
— how standards can be used at a global level and at an organizational level for the benefit of citizens; and
— processes for smart city ecosystem privacy protection.
This document is applicable to all types and sizes of organizations,…
Privacy protection — Privacy guidelines for smart cities
The document takes a multiple agency as well as a citizen-centric viewpoint.
It provides guidance on:
— smart city ecosystem privacy protection;
— how standards can be used at a global level and at an organizational level for the benefit of citizens; and
— processes for smart city ecosystem privacy protection.
This document is applicable to all types and sizes of organizations,…
Instruments and software used for measurements in high-voltage and high-current tests - Part 1: Requ...
IEC 61083-1:2021 is applicable to digital recorders, including digital oscilloscopes, used for measurements during tests with high impulse voltages and high impulse currents. It specifies the measuring characteristics and calibrations required to meet the measuring uncertainties and procedures specified in IEC 60060-2 and IEC 62475.
This document
• defines the terms specifically related to…
Health informatics — Automatic identification and data capture marking and labelling — Subject of ca...
This document outlines the standards needed to identify and label the Subject of Care (SoC) and the Individual Provider on objects such as identification (wrist) bands, identification tags or other objects, to enable automatic data capture using data carriers in the care delivery process.
It provides for a unique SoC identification that can be used for other purposes, such as recording the…
