Rechercher

Affiner les résultats
Code de la Classification internationale pour les normes (ICS)
Source
Code de l’organisme d’élaboration de normes (OEN)
Langue
Statut
Code de la Norme nationale du Canada (NNC)
Date de publication

De

à

Affichage 26171 - 26180 de 28585
Information Processing Systems - Open Systems Interconnection - Basic Connection Oriented Session P...
This National Standard is equivalent to International Standard ISO 8327:1987. It specifies: a) procedures for a single protocol for the transfer of data and control information from one session entity to a peer session entity; b) the means of selecting the functional units to be used by the session entities; c) the structure and encoding of the session protocol data units used…
Éditeur :
CSA
Statut :
Annulée
Date de publication :
1988-01-31
Code(s) de l'ICS :
35.100.50
Textile Test Methods Conditioning Textile Materials for Testing
Describes a procedure for conditioning textile materials to moisture equilibrium with the standard atmosphere.
Éditeur :
ONGC
Statut :
Annulée
Date de publication :
1988-01-31
Code(s) de l'ICS :
59.080.01
Specialty Transformers
1. Scope 1.1 This Standard applies to dry type, air-cooled transformers, autotransformers (fixed and variable), and primary-circuit reactors intended for use in, on, or associated with other approved equipment in capacities of 1000 kV·A and less and for primary voltages of 750 V or less, 60 Hz and less, and intended for use in nonhazardous locations in accordance with the Canadian…
Éditeur :
CSA
Statut :
Annulée
Date de publication :
1988-01-30
Code(s) de l'ICS :
29.180
Motors with Inherent Overheating Protection
1. Scope 1.1 This Standard applies to ac and dc motors with inherent overheating protection designed to be used in accordance with the Rules of the Canadian Electrical Code, Part I, as follows: (a) motors with a voltage rating not exceeding 600 V and with a protective device connected in the motor circuits; (b) impedance protected motors with a voltage rating not exceeding 600 V; and (c…
Éditeur :
CSA
Statut :
Annulée
Date de publication :
1988-01-30
Code(s) de l'ICS :
29.160.30
Equipment Wires
1. Scope 1.1 This Standard applies to insulated conductors intended for internal wiring in electrical equipment, but not as circuit conductors for use in raceways except where permitted by the Canadian Electrical Code, Part I. 1.2* Constructions covered by this Standard are (a) single-conductor, thermoplastic-insulated (Clause 5): (i) Type TXF, 60
Éditeur :
CSA
Statut :
Annulée
Date de publication :
1988-01-30
Code(s) de l'ICS :
29.060.10
Asbestos-cement sheets - Control and testing methods
1.1 This standard covers the inspection and test methods for the verification of dimensional, mechanical and physical properties of flat, corrugated, grooved or fluted asbestos-cement sheets, as well as those of shingles, bulkheading, molded roofing sheets and pavements tiles. 1.2 This standard includes the following control and testing methods : a) control of geometric…
Éditeur :
BNQ
Statut :
Annulée
Date de publication :
1988-01-29
Code(s) de l'ICS :
91.100.10
Aerospace — "P" clamps (loop clamps) for fluid systems — Envelope dimensions
Specifies maximum and minimum dimensions for these clamps installed by means of a bolt with a nominal diameter of 5 mm. The specified dimensions define a dimensional envelope. Shall not be considered as an interchangeability standard. The tolerances for each type of clamp are to be defined in the parts standards drawings.
Éditeur :
ISO
Statut :
Publié
Date de publication :
1988-01-27
Code(s) de l'ICS :
49.080
Aéronautique et espace — Colliers en P pour systèmes de fluides — Dimensions d'encombrement
La présente Norme internationale fixe les cotes maximales et minimales des colliers en P fixés à l'aide d'une vis de diamètre nominal 5 mm. Les dimensions fixées définissent une enveloppe dimensionnelle. La présente Norme internationale ne doit pas être considérée comme une norme d'interchangeabilité. Les tolérances pour chaque type de collier sont à définir dans les dessins de…
Éditeur :
ISO
Statut :
Publié
Date de publication :
1988-01-27
Code(s) de l'ICS :
49.080
Pyrometric reference cones for laboratory use — Specification
Specifies the characteristics of a standard series of pyrometric reference cones, which are used for determining the pyrometric cone equivalent (refractoriness) of refractory materials, over the temperature range 1500 to 1800 C. The cones specified in this International Standard are suitable for use in the procedure described in ISO 528, excluding determinations at 1500 and 1800 C.
Éditeur :
ISO
Statut :
Publié
Date de publication :
1988-01-27
Code(s) de l'ICS :
17.200.20
Soils - Determination of Permeability at the End of a Casing
Describes the method used to determine the coefficient of permeability of a soil at the end of a casing. The test consists in injecting water using gravity, into a soil through the lower opening of a drilling casing. This opening is located below the local piezometric level. Two test methods are described in the standard: a) the constant head method; b) the variable falling head…
Éditeur :
BNQ
Statut :
Annulée
Date de publication :
1988-01-14
Code(s) de l'ICS :
19.060; 13.080

Spacer