Wind turbines - Part 13: Measurement of mechanical loads
IEC 61400-13:2015(B) describes the measurement of fundamental structural loads on wind turbines for the purpose of the load simulation model validation. The standard prescribes the requirements and recommendations for site selection, signal selection, data acquisition, calibration, data verification, measurement load cases, capture matrix, post-processing, uncertainty determination and reporting…
Recommendations for renewable energy and hybrid systems for rural electrification - Part 6: Acceptan...
IEC TS 62257-6:2015(E) describes the various rules to be applied for acceptance, operation, maintenance and replacement of decentralized rural electrification systems which are designed to supply electric power for sites which are not connected to a large interconnected system, or a national grid, in order to meet basic needs. This technical specification proposes a methodology to achieve the…
Recommendations for renewable energy and hybrid systems for rural electrification - Part 4: System s...
IEC TS 62257-4:2015(E) provides a method for describing the results to be achieved by the electrification system independently of the technical solutions that could be implemented. The purpose is to provide a method to assist project contractors and project developers to select and design the electrification system for isolated sites while matching the identified needs, such as those described in…
Recommendations for renewable energy and hybrid systems for rural electrification - Part 5: Protecti...
IEC TS 62257-5:2015(E) specifies the general requirements for the protection of persons and equipment against electrical hazards to be applied in decentralised rural electrification systems. Requirements dealing with protection against electric shock are based on basic rules from IEC 61140 and IEC 60364. Decentralized Rural Electrification Systems are designed to supply electric power for sites…
Ships and marine technology — Offshore wind energy — Supply chain information flow
ISO 29404:2015 specifies content and format of the messages initiating and controlling the physical movement of wind turbine generator (WTG) components from suppliers to the construction site during the construction phase as well as for repair and maintenance purposes.
ISO 29404:2015 is applicable to all organizations involved in the production, transportation, storage and installation of WTG…
Metallic communication cable test methods - Part 4-7: Electromagnetic compatibility (EMC) - Test met...
IEC 62153-4-7:2015 describes a triaxial method, suitable to determine the surface transfer impedance and/or screening attenuation and coupling attenuation of mated screened connectors (including the connection between cable and connector) and cable assemblies. This method could also be extended to determine the transfer impedance, coupling or screening attenuation of balanced or multipin…
Metallic communication cable test methods - Part 4-7: Electromagnetic compatibility (EMC) - Test met...
IEC 62153-4-7:2015 describes a triaxial method, suitable to determine the surface transfer impedance and/or screening attenuation and coupling attenuation of mated screened connectors (including the connection between cable and connector) and cable assemblies. This method could also be extended to determine the transfer impedance, coupling or screening attenuation of balanced or multipin…
Non-destructive testing — Characterization and verification of ultrasonic phased array equipment — P...
ISO 18563-3:2015 addresses ultrasonic test systems implementing linear phased array probes, in contact (with or without wedge) or in immersion, with centre frequencies in the range of 0,5 MHz?10 MHz.
It provides methods and acceptance criteria for verifying the performance of combined equipment (i.e. instrument, probe and cables connected). The methods described are suitable for users working…
Petroleum and natural gas industries — Specific requirements for offshore structures — Part 1: Metoc...
ISO 19901-1:2015 gives general requirements for the determination and use of meteorological and oceanographic (metocean) conditions for the design, construction and operation of offshore structures of all types used in the petroleum and natural gas industries.
The requirements are divided into two broad types:
- those that relate to the determination of environmental conditions in general,…
Cigarettes — Determination of loss of tobacco from the ends — Part 3: Method using a vibro-bench
ISO/TS 3550-3:2015 specifies a method for the determination of loss of tobacco from cigarette ends using a vibro-bench.
This method applies to the determination of loss of tobacco from cigarette ends in manufacturing site, throughout the distribution network and also while in the smoker's pocket.
NOTE Two other methods for the determination of loss of tobacco from the ends, using a…
