Quick Disconnect Devices for use with Gas Fuel Appliances
1.1 Scope
1.1.1 This standard applies to newly-produced, hand-operated quick-disconnect devices, hereinafter also referred to as devices, constructed entirely of new, unused parts and materials which provide a means for connecting and disconnecting appliances or appliance connectors to gas supplies and which are for indoor and outdoor applications. These devices shall be equipped with…
Low-Pressure Hose Assemblies for use with Medical Gases
This National Standard of Canada is based on International Standard ISO 5359:2000 (second edition, 2000-11-01).
Scope
1.1
This International Standard specifies requirements for low-pressure hose assemblies intended for use with the following medical gases:
- oxygen;
- nitrous oxide;
- air for breathing;
- helium;
- carbon dioxide;
- xenon;
- specified mixtures of the gases listed above;
- air…
Agricultural Wheeled Tractors - Rear-mounted Three-point Linkage - Part 1: Categories 1, 2, 3 and 4
This National Standard of Canada is based on International Standard ISO 730-1:1994, third edition, 1994-12-15, including Technical Corrigendum 1:1995.
1 Scope
This part of IS0 730 specifies the dimensions and requirements of the three-point linkage for the attachment of implements or equipment to the rear of agricultural wheeled tractors.
It specifies four categories to be used on different…
1 Scope
Notes:
(1) For requirements pertaining to loads acting on connectors, see CSA S304.1.
(2) For requirements pertaining to installation of masonry connectors, see CSA A371.
1.1
This Standard specifies minimum requirements for designing the following masonry connectors:
(a) ties used to
(i) interconnect the wythes of a masonry wall; or
(ii) attach masonry veneer to its structural backing…
Compatibilité électromagnétique (CEM) - Partie 2-4: Environnement - Niveaux de compatibilité dans le...
La présente Norme nationale du Canada est équivalente à la Norme internationale CEI/IEC 61000-2-4:2002 (deuxième édition, 2002-06).
1 Domaine d'application
La présente partie de la CEI 61000 est relative aux perturbations conduites dans le domaine de fréquence de 0 kHz à 9 kHz. Elle fournit les valeurs numériques des niveaux de compatibilité pour les réseaux de distribution d'énergie…
Electromagnetic Compatibility (EMC) - Part 2: Environment - Section 6: Assessment of the Emission Le...
This National Standard of Canada is equivalent to International Standard CEI/IEC 1000-2-6:1995 (first edition, 1995-09).
1 Scope
This technical report recommends the procedures to assess the disturbance levels produced by the emission of the devices, equipment and systems installed in non-public networks in industrial environment as far as the low-frequency conducted disturbances in the power…
Compatibilité électromagnétique (CEM) - Partie 2: Environnement - Section 6: Évaluation des niveaux ...
La présente Norme nationale du Canada est équivalente à la Norme internationale CEI/IEC 1000-2-6:1995 (première édition, 1995-09).
1 Domaine d'application
Ce guide recommande les procédures destinées à évaluer les niveaux de perturbation produits par l'émission des appareils, des équipements et systèmes installés dans les réseaux non publics en environnement industriel en ce qui…
ISO 7840:2004 specifies general requirements and physical tests for fire-resistant hoses for conveying petrol and diesel oil, designed for a working pressure not exceeding 0,34 MPa for hoses with nominal bore up to and including 10 mm and 0,25 MPa for hoses with larger bore in craft of hull length up to 24 m.
ISO 7840:2004 applies to hoses for small craft with permanently installed fuel systems.…
Agricultural vehicles — Mechanical connections between towed and towing vehicles — Part 4: Dimension...
ISO 6489-4:2004 specifies the dimensional requirements for the piton-type coupling devices used in the attachment to agricultural towing vehicles of towed, non-balanced trailers and implements equipped with a coupling ring specified in ISO 5692-1. Its purpose is to ensure the interchangeability of the mechanical connections on agricultural towing vehicles. It is applicable only in those cases…
Information technology - Home electronic system - Guidelines for product interoperability - Part 1: ...
Specifies requirements for product interoperability in the area of home and building automation systems, with sufficient detail needed to design interoperable Home Electronic System products. The widespread development of many national standard and proprietary networks within and to the home has necessitated a standard for interoperability among home system applications and products from multiple…
