Domestic gas cooking appliances — Safety — Part 1: General requirements
This document specifies the safety requirements for domestic gas cooking appliances. These appliances are freestanding, built-in or table-top and are intended to be used indoors. This document applies to the gas sections of the appliances and their component parts (e.g. combined gas-electric cooking appliances). This document does not apply to:
a) electrical heated elements as part of the…
Dentistry — Coupling dimensions for handpiece connectors — Part 1: Mechanical properties
This International Standard specifies the coupling between handpieces and motors connected to dental units.
This International Standard specifies the nominal dimensions, tolerances and the extraction force of coupling systems for use between handpiece and motor which supply the handpiece with water, air and light, and rotation energy.
Domestic gas cooking appliances — Safety — Part 22: Particular requirements for ovens and compartmen...
This document specifies particular requirements for safety, construction and materials of domestic gas ovens and compartment grills. For general requirements for safety, construction and materials of gas ovens and compartment grills, ISO/TS 21364-1:2021 applies.
This document covers the following gas cooking appliances:
— ovens with natural or forced convection;
— pyrolytic-self-cleaning…
Domestic gas cooking appliances — Safety — Part 21: Particular requirements for gas hobs, gas grills...
This document specifies particular requirements for safety, construction and materials of household gas surface cooking appliances. For general requirements for safety, construction and materials of gas hobs, see ISO/TS 21364-1:2021.
This document covers the following:
— surface cooking appliances:
— hobs;
— surface grills;
— griddles;
being built-in, part of a cooking appliance or…
Aircraft — Passenger doors interface requirements for connection of passenger boarding bridge or pas...
ISO 7718-1:2016 specifies minimum requirements for dimensions and unobstructed space around main deck passenger doors of future types of civil-passenger transport aircraft when they are intended to be compatible with the thousands of passenger boarding bridges and passenger transfer vehicles existing, or being planned, in airports worldwide.
ISO 7718-1:2016 is not applicable to existing models of…
Road vehicles — Local Interconnect Network (LIN) — Part 3: Protocol specification
ISO 17987-3:2016 specifies the LIN protocol including the signal management, frame transfer, schedule table handling, task behaviour and status management and LIN master and slave node. It contains also OSI layer 5 properties according to ISO 14229‑7 UDSonLIN-based node configuration and identification services (SID: B016 to B816) belonging to the core protocol specification.
A node (normally a…
Small bore connectors for liquids and gases in healthcare applications — Part 6: Connectors for neur...
ISO 80369-6:2016 specifies requirements for small-bore connectors intended to be used for connections in neuraxial applications. Neuraxial applications involve the use of medical devices intended to administer medications to neuraxial sites, wound infiltration anaesthesia delivery, and other regional anaesthesia procedures or to monitor or remove cerebro-spinal fluid for therapeutic or diagnostic…
Road vehicles — Local Interconnect Network (LIN) — Part 4: Electrical physical layer (EPL) specifica...
ISO 17987-4:2016 specifies the 12 V and 24 V electrical physical layers (EPL) of the LIN communications system.
The electrical physical layer for LIN is designed for low-cost networks with bit rates up to 20 kbit/s to connect automotive electronic control units (ECUs). The medium that is used is a single wire for each receiver and transmitter with reference to ground.
ISO 17987-4:2016 includes…
Dentistry — General requirements for instruments and related accessories used in dental implant plac...
ISO 13504:2012 specifies general requirements for the manufacture of instruments and related accessories used in the placement of dental implants and further manipulations of connecting parts in the craniofacial area.
It is applicable to single-use and reusable instruments, regardless of whether they are manually driven or connected to a power-driven system.
Piping systems for rehabilitation of underground gas supply networks — Part 1: Polyethylene (PE) mat...
This document specifies requirements and test methods for pipes and fittings which are part of piping systems for the rehabilitation by means of renovation and trenchless replacement of underground gas supply networks.
It is applicable to polyethylene (PE) pipes, fittings and assemblies, as manufactured and as installed. It is not applicable to the existing pipeline.
It is applicable to…
