Information technology - Security techniques - Information security incident management - Part 2: G...
ISO/IEC 27035-2:2016 provides the guidelines to plan and prepare for incident response. The guidelines are based on the "Plan and Prepare" phase and the "Lessons Learned" phase of the "Information security incident management phases" model presented in ISO/IEC 27035‑1.
The major points within the "Plan and Prepare" phase include the following:
-…
Vehicles, boats and internal combustion engines - Radio disturbance characteristics - Limits and met...
CISPR 25:2016 contains limits and procedures for the measurement of radio disturbances in the frequency range of 150 kHz to 2 500 MHz. The standard applies to any electronic/electrical component intended for use in vehicles, trailers and devices. Refer to International Telecommunications Union (ITU) publications for details of frequency allocations. The limits are intended to provide protection…
Metallic materials — Instrumented indentation test for hardness and materials parameters — Part 4: T...
ISO 14577-4:2016 specifies a method for testing coatings which is particularly suitable for testing in the nano/micro range applicable to thin coatings. However, the application of this method of this part of ISO 14577 is not needed if the indentation depth is such a small fraction of the coating thickness that in any possible case a substrate influence can be neglected and the coating can be…
Earth-moving machinery — Electrical safety of machines utilizing electric drives and related compone...
ISO 14990-2:2016 the particular safety requirements for the electrical equipment and its components incorporated in externally-powered (mains-connected, including machines powered by external dedicated generators), electrically-driven earth-moving machines (EMMs).
It is applicable to those machines using on-board voltages in the range of 50 V?36 kV AC r.m.s. at any frequency and 75 V?36 kV DC ?…
High-voltage switchgear and controlgear - Part 212: Compact Equipment Assembly for Distribution Subs...
IEC 62271-212:2016 specifies the service conditions, rated characteristics, general structural requirements and test methods of the assemblies of the main electrical functional units of a high-voltage/low-voltage distribution substation, duly interconnected, for alternating current of rated operating voltages above 1 kV and up to and including 52 kV on the high-voltage side, service frequency 50…
Nanomanufacturing - Key control characteristics - Part 4-4: Nano-enabled electrical energy storage -...
IEC TS 62607-4-4:2016(E), which is a Technical Specification, provides a measurement method for thermal runaway quality level test for nano-enabled energy storage devices. This method uses comparative measurement to enable a manufacturer to decide whether or not the nanomaterial additives used in energy storage devices are resilient against the thermal runaway caused by a faulty or accidental low…
Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-1...
This group safety publication is primarily intended to be used as a product safety standard for the products mentioned in the scope, but shall also be used by technical committees in the preparation of their publications for products similar to those mentioned in the scope of this standard, in accordance with the principles laid down in IEC Guide 104 and lSO/lEC Guide 51.
IEC 61010-2-120:2016…
Exigences de sécurité pour appareils électriques de mesurage, de régulation et de laboratoire - Part...
La présente publication groupée de sécurité est avant tout destinée à être utilisée en tant que norme en matière de sécurité des produits pour les produits cités dans le domaine d'application, mais elle doit également être utilisée par les comités d'études dans le cadre de l'élaboration de leurs publications pour des produits similaires à ceux cités dans le domaine d'…
Medical electrical equipment - Part 2-58: Particular requirementsfor the basic safety and essential ...
IEC 80601-2-58:2014+A1:2016 applies to the basic safety and essential performance of lens removal devices and vitrectomy devices for ophthalmic surgery and associated accessories that can be connected to this medical electrical equipment, hereafter referred to as ME equipment. Hazards inherent in the intended physiological function of ME equipment or ME systems within the scope of this standard…
Geotechnical investigation and testing — Geotechnical monitoring by field instrumentation — Part 2: ...
ISO 18674-2:2016 specifies the measurement of displacements along a line by means of extensometers carried out for geotechnical monitoring. General rules of performance monitoring of the ground, of structures interacting with the ground, of geotechnical fills and of geotechnical works are presented in ISO 18674‑1.
If applied in conjunction with ISO 18674‑3, this document allows the determination…
