Intelligent transport systems — Cooperative ITS — Part 1: Roles and responsibilities in the context ...
This document contains a detailed description of the (actor invariant) roles (3.22) and responsibilities (3.21) required to deploy and operate Cooperative-ITS (C-ITS) (3.8). The organization/organization of actors / roles described in this document are designed to be appropriate for any fully operational system that uses the C-ITS concepts and techniques in order to achieve its service provision…
Leather — Chemical determination of chromic oxide content — Part 3: Quantification by atomic absorpt...
This document describes a method for the determination of chromium in aqueous solution obtained from leather. This is an analysis for total chromium in leather; it is not compound specific or specific to its oxidation state.
This method describes the determination of chromium by atomic absorption spectrometry and is applicable to leathers which are expected to have chromic oxide contents in…
Sterilization of health care products — VocabularyStérilisation des produits de santé — Vocabulaire
This Technical Specification gives definitions of
terms in the field of sterilization technology.
This Technical Specification does not provide
requirements for the validation and routine control of
a sterilization process, but is intended to contribute
fundamentally towards mutual understanding
amongst those preparing and using International
Standards in the field of sterilization…
Magnetic materials - Part 6: Methods of measurement of the magnetic properties of magnetically soft ...
IEC 60404-6:2018 RLV contains both the official IEC International Standard and its Redline version. The Redline version is available in English only and provides you with a quick and easy way to compare all the changes between the official IEC Standard and its previous edition.
IEC 60404-6:2018 specifies methods for the measurement of AC magnetic properties of soft magnetic materials, other…
Magnetic materials - Part 6: Methods of measurement of the magnetic properties of magnetically soft ...
IEC 60404-6:2018 specifies methods for the measurement of AC magnetic properties of soft magnetic materials, other than electrical steels and soft ferrites, in the frequency range 20 Hz to 100 kHz. The materials covered by this part of IEC 60404 include those speciality alloys listed in IEC 60404-8-6, amorphous and nano-crystalline soft magnetic materials, pressed and sintered and metal injection…
Specification of technical grade sulphur hexafluoride (SF<sub>6</sub>) and complementary...
IEC 60376:2018 defines the quality for technical grade sulphur hexafluoride (SF<sub>6</sub>) and complementary gases such as nitrogen (N<sub>2</sub>) and carbon tetra-fluoride (CF<sub>4</sub>), for use in electrical equipment. Detection techniques, covering both laboratory and in-situ portable instrumentation, applicable to the analysis of SF<sub>6</…
Specification of technical grade sulphur hexafluoride (SF<sub>6</sub>) and complementary...
IEC 60376:2018 defines the quality for technical grade sulphur hexafluoride (SF6) and complementary gases such as nitrogen (N2) and carbon tetra-fluoride (CF4), for use in electrical equipment. Detection techniques, covering both laboratory and in-situ portable instrumentation, applicable to the analysis of SF6, N2 and CF4 gases prior to the introduction of these gases into the electrical…
Spécification de la qualité technique de l'hexafluorure de soufre (SF<sub>6</sub>) ...
L'IEC 60376:2018 définit la qualité technique de l'hexafluorure de soufre (SF6) et des gaz complémentaires (l'azote (N2) et le tétrafluorure de carbone (CF4), par exemple) utilisés dans les matériels électriques. Le présent document décrit également les techniques de détection couvrant les instruments de laboratoire et les instruments portables in situ, applicables à l'analyse…
Interfaces de bus universel en série pour les données et l'alimentation électrique - Partie 1-3...
IEC 62680-1-3:2018 définit les connecteurs mâles et femelles, ainsi que les câbles USB Type-C™.
La spécification des câbles et connecteurs USB Type-C est guidée par les principes suivants:
- favoriser des critères de forme d'hôtes et dispositifs innovants et agréables, pour lesquels la taille, la conception industrielle et le style sont des paramètres importants;
- travailler en toute…
Classes de qualité de surface des barres et fils-machine laminés à chaud
Le présent document spécifie les spécifications techniques de livraison relatives à la qualité de surface des barres de section ronde, carrée, hexagonale et du fil machine en acier laminé à chaud avec des dimensions nominales dN compris entre 5 mm et 200 mm. Le présent document est applicable aux produits transformés à froid et aux aciers à outils, si cela est convenu au moment de l'appel d…
