Hand-Held Motor-Operated Electric Tools - Safety - Part 1: General Requirements
This National Standard of Canada is based on International Standard IEC 60745-1:2003, and is joint with UL 60745-1.
1 Scope
1.1
This International Standard deals with the safety of hand-held motor-operated or magnetically driven electric tools, the rated voltage of the tools being not more than 250 V for single-phase a.c. or d.c. tools, and 440 V for three-phase a.c. tools.
So far as is…
Hand-Held Motor-Operated Electric Tools - Safety - Part 2-9: Particular Requirements for Tappers
This National Standard of Canada is equivalent to International Standard IEC 60745-2-9:2003, and is joint with UL 60745-2-9.
1 Scope
This clause of Part 1 is applicable except as follows:
1.1 Addition:
This standard applies to tappers.
Hand-Held Motor-Operated Electric Tools Safety Part 2-11: Particular Requirements for Reciprocating ...
This National Standard of Canada is based on International Standard IEC 60745-2-11:2003, and is joint with UL 60745-2-11.
1 Scope
This clause of Part 1 is applicable, except as follows:
1.1 Addition:
This standard applies to reciprocating saws.
Tools covered by this standard include but are not limited to jigsaws and reciprocating saws (sabre saws).
Hand-Held Motor-Operated Electric Tools - Safety - Part 2-14: Particular Requirements for Planers
This National Standard of Canada is based on International Standard IEC 60745-2-14:2003, and is joint with UL 60745-2-14.
1 Scope
This clause of Part 1 is applicable except as follows:
1.1 Addition:
This standard applies to planers.
Hand-Held Motor-Operated Electric Tools - Safety - Part 2-17: Particular Requirements for Routers an...
This National Standard of Canada is based on International Standard IEC 60745-2-17:2003, and is joint with UL 60745-2-17.
1 Scope
This clause of Part 1 is applicable except as follows:
1.1 Addition:
This standard applies to routers and trimmers.
Environmental Management Systems for Hog Operations: Requirements
1 Scope
This Standard specifies the requirements for an environmental management system (EMS) for hog operations. This Standard can be applied to hog operations or livestock operations containing hogs.
This Standard is intended to be used by hog operations that wish to have their EMS registered by a nationally accredited third-party registration body.
Low-Pressure Hose Assemblies for use with Medical Gases
This National Standard of Canada is based on International Standard ISO 5359:2000 (second edition, 2000-11-01).
Scope
1.1
This International Standard specifies requirements for low-pressure hose assemblies intended for use with the following medical gases:
- oxygen;
- nitrous oxide;
- air for breathing;
- helium;
- carbon dioxide;
- xenon;
- specified mixtures of the gases listed above;
- air…
Handbook on Infection Control in Office-Based Health Care and Allied Services
This handbook has been developed to answer general questions common to all health care practices and personal services.
- How do I process an instrument after I have used it on a patient or client?
- What kind of disinfectant should I use?
- What kind of sterilizer should I use and do I really need one? - How do I dispose of a contaminated article?
- What should I do with needles and other…
Agricultural Wheeled Tractors - Rear-mounted Three-point Linkage - Part 1: Categories 1, 2, 3 and 4
This National Standard of Canada is based on International Standard ISO 730-1:1994, third edition, 1994-12-15, including Technical Corrigendum 1:1995.
1 Scope
This part of IS0 730 specifies the dimensions and requirements of the three-point linkage for the attachment of implements or equipment to the rear of agricultural wheeled tractors.
It specifies four categories to be used on different…
1 Scope
1.1
This Standard specifies minimum requirements for masonry materials and masonry construction.
Notes:
(1) Requirements for structural design of masonry are specified in CSA S304.1.
(2) If a requirement specified in Part 9 of the National Building Code of Canada differs from a requirement specified
in this Standard, the requirement specified in this Standard should be followed.
1.2…
