Rechercher

IEC 60335-2-25:2010+A1:2014 deals with the safety of microwave ovens for household and similar use, their rated voltage being not more than 250 V. This standard also deals with combination microwave ovens, for which Annex AA is applicable. This standard also deals with microwave ovens intended to be used on board ships, for which Annex BB is applicable. Appliances not intended for normal…

1.1 The requirements of this Standard apply to the following electrical equipment for elevators, escalators, moving walks, dumbwaiters, material lifts, and elevating devices for persons with physical disabilities (platform lifts and stairway chairlifts): (a) motor controllers; (b) motion controllers; (c) operation controllers; (d) operating devices; and (e) all other electrical equipment…

1 Scope 1.1 This Standard applies to newly produced non-metallic dip tubes intended for use in water heaters. 1.2 Compliance of a dip tube with this Standard does not imply that such dip tube is acceptable for use in water heaters without supplemental tests with the dip tube installed in the particular water heater design. 1.3 This standard contains SI (Metric) corresponding to the yard/pound…

1.1 General This Standard specifies requirements for the structural design of unreinforced, reinforced, and prefabricated masonry structures and components in accordance with the limit states design method of the National Building Code of Canada. This Standard also provides requirements for the structural design of prestressed masonry beams, walls, and columns in accordance with the limit…

ISO/TS 17427:2014 describes the (actor invariant) roles and responsibilities required to deploy and operate Cooperative-ITS (C-ITS). The organizational architecture described in this document is to be used for a fully operational system. ISO/TS 17427:2014 is couched in terms of an organizational or enterprise viewpoint, as defined in ISO/IEC 10746 Open Distributed Processing. ISO/TS 17427:2014…

1.1 These requirements cover liquid-tight flexible nonmetallic conduit in the 3/8 – 4 (12 – 103) trade sizes of Type LFNC-A (Layered), Type LFNC-B (Integral), and Type LFNC-C (Corrugated) constructions. The conduit is intended for installation in accordance with the National Electrical Code (NEC) and the Canadian Electrical Code (CEC), Part 1. The values in parentheses are metric trade…

1 Domaine d’application 1.1 Ce code vise l’installation, l’inspection, la réparation et l’entretien du système d’entreposage et de distribution de carburant qui équipe les chariots de manutention à moteur et les véhicules routiers destinés à être alimentés au gaz naturel comprimé (GNC) ou les portions au gaz naturel comprimé d’un système de gaz naturel liquéfié (GNL). Les systèmes d’…

This National Standard of Canada is based on International Standard IEC 60871-1:2005, MOD. This part of IEC 60871 is applicable to both capacitor units and capacitor banks intended to be used, particularly, for power-factor correction of a.c. power systems having a rated voltage above 1 000 V and frequencies of 15 Hz to 60 Hz. This part of IEC 60871 also applies to capacitors intended for…

ISO 7240-15:2014 specifies requirements, test methods, and performance criteria for point-type fire detectors using smoke and heat sensors, incorporating in one mechanical enclosure at least one smoke sensor and at least one other sensor which responds to heat, and in which the signal(s) of the smoke sensor(s) is (are) combined with the signal(s) of the heat sensor(s). The performance of a single…

ISO 14532:2014 establishes the terms, definitions, symbols, and abbreviations used in the field of natural gas. The terms and definitions have been reviewed and studied in order to cover all aspects of any particular term with input from other sources such as European Standards from CEN (The European Committee for Standardization), national standards, and existing definitions in the IGU…