Fibre optic interconnecting devices and passive components - Part 06: Mechanical design proving nuta...
IEC/TR 62627-06:2014 which is a technical report, describes the results of mechanical design proving tests for a high density systems application, carried out using the nutation test according to IEC 61300-2-35, performed on reinforced fibre cable terminated with optical connectors. A tensile load is suggested for the design proving requirements to be used to ensure that connectors meet the…
Timber structures — Strength graded timber — Test methods for structural properties
ISO 13910:2014 specifies test procedures for full-size sawn timber that has been strength-graded, for the derivation of design properties in codes dealing with structural engineering design. It is applicable to sawn timber of rectangular cross-section subjected to a short-duration load.
Road vehicles — Fuse-links — Part 9: Fuse-links with shortened tabs (Type K)
ISO 8820-9:2014 specifies fuse-links with shortened tabs (Type K) for use in road vehicles. It establishes, for these fuse-link types, the rated current, test procedures, performance requirements, and dimensions.
ISO 8820-9:2014 is applicable to fuse-links with a rated voltage of 58 V, a current rating of ≤ 30 A, and a breaking capacity of 1 000 A intended for use in road vehicles.
ISO 8820-9:…
Papier tissue et produits tissue — Partie 7: Détermination des propriétés optiques — Mesurage du deg...
L'ISO 12625-7:2014 spécifie des modes opératoires d'essai pour la détermination instrumentale du degré de blancheur et de la couleur des papiers tissue et des produits tissue dans les conditions de lumière du jour extérieure. Elle donne également des instructions spécifiques pour la préparation des éprouvettes (produits à pli unique, produits multiplis) ainsi que pour les mesures…
Tissue paper and tissue products — Part 7: Determination of optical properties — Measurement of brig...
ISO 12625-7:2014 specifies testing procedures for the instrumental determination of brightness and colour of tissue paper and tissue products viewed under outdoor daylight conditions. It also gives specific instructions for the preparation of test pieces (single-ply, multi-ply products) and for the optical measurements of products, where special precautions may be necessary.
Performance hygrothermique des équipements de bâtiments et installations industrielles — Calcul de l...
L'ISO 15758:2014 donne une méthode permettant de calculer la densité du flux de vapeur d'eau dans les systèmes d'isolation de tuyauteries froides, ainsi que la quantité totale d'eau diffusée dans l'isolation au cours du temps. La méthode de calcul suppose que la vapeur d'eau ne peut migrer dans le système d'isolation que par diffusion, sans aucune contribution d…
Hygrothermal performance of building equipment and industrial installations — Calculation of water v...
ISO 15758:2014 specifies a method for calculating the density of the water vapour flow rate in cold pipe insulation systems, and the total amount of water diffused into the insulation over time. The calculation method presupposes that water vapour can only migrate into the insulation system by diffusion, with no contribution from airflow. It also assumes the use of homogeneous, isotropic…
Timber structures — Test methods — Torsional resistance of driving in screws
ISO 17754:2014 specifies a test method to determine the torsional resistance to driving of screws in solid timber or glued laminated timber or other wood-based materials. The method is used primarily to ensure the torque that may be applied to install screws will be less than the specified failure torque of the screw.
1.1
Cette norme vise les chaussures de protection neuves et définit deux catégories de résistance aux chocs
de l’embout protecteur. Elle établit également des exigences spéciales visant la tenue de la semelle, la
protection métatarsienne et la protection contre les chocs électriques, la durabilité de la souplesse de la
semelle, la conductivité et les éléments de protection pour utilisateurs…
