Measurement procedures for materials used in photovoltaic modules - Part 1-5: Encapsulants - Measure...
IEC 62788-1-5:2016 provides a method for measuring the maximum representative change in linear dimensions of encapsulation sheet material in an unrestricted thermal exposure as might or might not be seen during photovoltaic (PV) module fabrication. Data obtained using this method may be used by encapsulation material manufacturers for the purpose of quality control of their encapsulation material…
Procédures de mesure des matériaux utilisés dans les modules photovoltaïques - Partie 1-5: Encapsula...
L'IEC 62788-1-5:2016 fournit une méthode de mesure de la variation maximale représentative des dimensions linéaires des matériaux d'encapsulation en couches minces dans le cas d'une exposition thermique non limitée qui pourrait se produire au cours de la fabrication de modules photovoltaïques (PV). Les données obtenues avec cette méthode peuvent être utilisées par les fabricants de…
Solid biofuels — Conversion of analytical results from one basis to another
ISO 16993:2016 gives formulae which allow analytical data relating to solid biofuels to be expressed on the different bases in common use. Consideration is given to corrections that can be applied to certain determined values for solid biofuels prior to their calculation to other bases.
In Annex A, tools for integrity checks of analytical results are given. In Annex B, conversion factors for…
Caoutchouc naturel brut — Détermination de la teneur en impuretés
L'ISO 249 :2016 spécifie une méthode pour la détermination de la teneur en impuretés du caoutchouc naturel brut.
Elle n'est pas applicable aux impuretés présentes à la surface du caoutchouc par suite de contamination.
ISO 4301-1:2016 establishes a general classification of cranes and mechanisms based on the service conditions, mainly expressed by the following:
- the total number of working cycles to be carried out during the specified design life of the crane;
- the load spectrum factor which represents the relative frequencies of loads to be handled;
- the average displacements.
Additional information for…
Implants for surgery — Partial and total hip joint prostheses — Part 13: Determination of resistance...
ISO 7206-13:2016 describes a method of determining the torque required, under specified laboratory conditions, to loosen the fixation of the head of hip joint prostheses in which the head is not intended to rotate relative to the neck. It applies to the femoral component of total or partial hip joint replacements in which the head and neck/stem (in the following referred to as cone) are secured…
Soil quality — Determination of the toxic effects of pollutants on germination and early growth of h...
ISO 18763:2016 describes a technique for determining the effects of soil and soil-related materials on the seed germination and early growth of higher plants. These endpoints are useful indicators for the assessment of the quality of a soil as a habitat for organisms. It is applicable to all soils in which soil organisms are active and may be used to evaluate:
- the effects on plants due to…
Respiratory protective devices — Methods of test and test equipment — Part 5: Breathing machine, met...
ISO 16900-5:2016 specifies the characteristics of breathing machines, metabolic simulators, RPD head forms/torso, RPD tools and RPD verification tools that are common to RPD test laboratories. Standardization of these items is essential for the standardization of the test methods.
Standardization of the RPD verification tools is essential for demonstrating the delivery of comparable results in…
Qualité du sol — Détermination des effets toxiques des polluants sur la germination et les premiers ...
La présente Norme internationale décrit une méthode permettant de déterminer les effets de sols et de matériaux apparentés aux sols sur la germination des semences et les premiers stades de la croissance des végétaux supérieurs. Ces critères d'effet sont des indicateurs utiles pour l'évaluation de la qualité d'un sol en tant qu'habitat pour des organismes. La présente Norme…
