Séparateurs de graisses

Numéro de référence:
B481 SERIES-12
Catégorie de norme:
Norme consensuelle d'OEN
Type d’activité d’élaboration de normes:
Confirmation
Statut:
En cours d'élaboration
Date de début de la période de commentaires OEN:
Date de fin de la période de commentaires des OEN:
Affiché le:

Porté:

Champ d’application

1.1
This Standard specifies material, design, and construction requirements for manufactured grease interceptors intended to separate and collect organic fats, oils, and greases from water.

1.2
Grease interceptors covered in the CSA B481 Series

  1. are installed in drainage systems to reduce the amount of organic fats, oils, and greases entering the sanitary system;
  2. may be for indoor applications (usually referred to as the under-the-counter type) or for outdoor applications (i.e., underground);
  3. have a flow rating of not less than 26 L/min (7 gpm) and not more than 380 L/min (100 gpm); and
    Note: Grease interceptors can operate at any flow rate below their flow rating.
  4. are hydromechanical batch-flow interceptors.

1.3
The CSA B481 Series does not cover interceptors intended for rainwater, sanitary wastewater, or wastewater containing petroleum products such as gasoline, heating oils, or mineral oils.

1.4
In CSA Standards, "shall" is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; "should" is used to express a recommendation or that which is advised but not required; "may" is used to express an option or that which is permissible within the limits of the standard; and "can" is used to express possibility or capability.

Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material.

Notes to tables and figures are considered part of the table or figure and may be written as requirements.

Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

1.5
In the CSA B481 Series, the values given in SI (metric) units are the standard. Where values are given in parentheses, they are for information only.

Litres (metric liquid) per minute is abbreviated L/min and gallons (US liquid) per minute is abbreviated gpm. All references to gallons are to US liquid gallons.

----------------------------------------------------------------

B481.1-12 - Testing and rating of grease interceptors using lard
 

Scope

This Standard specifies performance criteria for the testing and rating of grease interceptors (as defined in CSA B481.0) using lard.

----------------------------------------------------------------

B481.2-12 - Testing and rating of grease interceptors using oil
 

Scope

This Standard specifies performance criteria for the testing and rating of grease interceptors (as defined in CSA B481.0) using oil.

----------------------------------------------------------------

B481.3-12 - Sizing, selection, location, and installation of grease interceptors
 

Scope

This Standard specifies sizing, selection, location, and installation requirements for grease interceptors (as defined in CSA B481.0).

----------------------------------------------------------------

B481.4-12 - Maintenance of grease interceptors
 

Scope

This Standard specifies requirements for the maintenance of grease interceptors manufactured, performance tested and rated, sized, selected, and installed in accordance with the CSA B481 Series.

----------------------------------------------------------------

B481.5-12 - Testing and rating of grease interceptors equipped with a grease removal device
 

Scope

This Standard specifies performance criteria for the testing and rating of grease interceptors equipped with an automatic grease removal device (GRD). Semi-automatic devices are not addressed in this Standard

Raison d’être du projet

Raison d’être du projet
na

Note : L’information ci-dessus a été recueillie et est diffusée par le Conseil canadien des normes (CCN) pour les besoins de son système de notification centralisé et transparent pour l’élaboration de nouvelles normes. Le système permet aux organismes d’élaboration de normes (OEN) accrédités par le CCN et aux membres du public d’être informés des nouveaux travaux d’élaboration de normes au Canada. Il donne aussi aux OEN accrédités la possibilité de repérer et de résoudre les cas de doubles emplois éventuels dans les normes et les travaux de normalisation.

Les OEN sont eux-mêmes responsables du contenu et de l’exactitude de l’information présentée ici. Cette information n’existe que dans la langue dans laquelle elle a été fournie au CCN.