Asphalt for Constructing Built-Up Roof Coverings and Waterproofing Systems
1 Scope
1.1
This Standard covers asphalt intended for use as hot cement and topcoat in the construction of built-up coverings on roof decks of various types and slopes and in the construction of waterproofing systems.
1.2
The following types of asphalt are covered by this Standard:
(a) Type I: asphalt for use on built-up roofs with slopes less than or equal to 1:16 and for use as waterproofing…
CSA Standards on Concrete Masonry Units (Consists of A165.1, A165.2 and A165.3)
A165.1-04 Concrete block masonry units
1 Scope
This Standard applies to concrete block masonry units made from cementitious materials, water, and aggregates, with or without the inclusion of other materials. This Standard may be applied to other units of similar manufacture and size within the limitations of the Standard.
Note: For concrete brick masonry units, see CSA A165.2. For prefaced…
1 Scope
1.1 General
This Standard specifies requirements for
(a) mortar for use in bedding, jointing, and bonding of masonry units; and
(b) grout for use in filling core, cell, or cavity space
in unit masonry construction.
Notes:
(1) The term "unit masonry" refers to masonry construction using clay (shale), calcium silicate (sand-lime), or concrete masonry units, with individual…
1 Scope
Notes:
(1) For requirements pertaining to loads acting on connectors, see CSA S304.1.
(2) For requirements pertaining to installation of masonry connectors, see CSA A371.
1.1
This Standard specifies minimum requirements for designing the following masonry connectors:
(a) ties used to
(i) interconnect the wythes of a masonry wall; or
(ii) attach masonry veneer to its structural backing…
1 Scope
1.1
This Standard specifies minimum requirements for masonry materials and masonry construction.
Notes:
(1) Requirements for structural design of masonry are specified in CSA S304.1.
(2) If a requirement specified in Part 9 of the National Building Code of Canada differs from a requirement specified
in this Standard, the requirement specified in this Standard should be followed.
1.2…
Certification of manufacturers of steel building systems
1 Scope
1.1
This Standard applies to the certification of manufacturers of steel building systems as defined in Clause 3.
1.2
This Standard prescribes the procedure for certification based on an audit of a manufacturer?s plant(s) and
facilities by the certification agency.
1.3
This Standard provides the requirements for a certificate of design and manufacturing conformance for
each…
1 Scope
1.1
This Code applies to
(a) the installation of appliances, equipment, components, and accessories where oil is used for fuel
purposes such as
(i) forced-air furnaces;
(ii) boilers;
(iii) domestic water heaters;
(iv) vehicle heaters; and
(v) emergency power supplies for buildings;
(b) the installation of all stationary and portable oil-burning equipment, including fuel…
1 Scope
1.1 General
This Standard applies to portable, integral chassis elevating work platforms with bases that cannot be
driven or moved horizontally while the platform is in an elevated position. The platform can be moved,
articulated, or adjusted by manual or powered means to position personnel, along with their necessary
tools and materials, at work locations. For the purpose of…
Electromagnetic Compatibility (EMC) - Part 2-4: Environment - Compatibility Levels in Industrial Pla...
This National Standard of Canada is equivalent to International Standard CEI/IEC 61000-2-4:2002 (second edition, 2002-06).
1 Scope
This part of IEC 61000 is concerned with conducted disturbances in the frequency range from 0 kHz to 9 kHz. It gives numerical compatibility levels for industrial and non-public power distribution systems at nominal voltages up to 35 kV and a nominal frequency of 50…
This is a Tri-national standard with ANCE NMX-J-017 and UL 514B.
1 Scope
1.1
These requirements cover FITTINGS for use with cable and conduit intended for installation in accordance with the National Electrical Code, ANSI/NFPA 70, the Canadian Electrical Code (CEC), Part I, CSA C22.1, and the Standard for Electrical Installations, NOM-001-SEDE.
1.2
These requirements cover CONDUIT LOCKNUTS,…