1.1
This Standard specifies the chassis and body requirements and safety equipment requirements for school buses. It is a manufacturing standard intended to apply to original equipment supplied by the bus manufacturer.
Note: The main purpose of this Standard is to provide the safest possible vehicle for students using school buses. It needs to be stressed, however, that standards are not…
Norme de rendement des climatiseurs et des thermopompes à deux blocs et monoblocs
1.1 Généralités
1.1.1
Cette norme s’applique à des climatiseurs et thermopompes unitaires qui sont :
a) fabriqués en usine ;
b) à l’air ou à écoulement d’air ;
c) des ensembles correspondant à deux blocs (y compris mini blocs et blocs multiples) ou monobloc ;
d) du type classé à l’article 1.2 ;
e) prévus pour la climatisation et le chauffage d’espaces dans des bâtiments ;
f) à entraînement…
1.1
This Standard applies to single-conductor and multi-conductor Type RA90 and RC90 cables having a maximum temperature rating of 90 °C in both dry and wet locations and intended for installation in accordance with CSA C22.1, Canadian Electrical Code, Part I.
1.2
Cables covered in this Standard are intended for use on systems having nominal voltages up to 5000 V, except for 2-conductor,…
1.1 This Standard applies to Class A, single- and three-phase, ground-fault circuit-interrupters intended
for protection of personnel, for use only in grounded neutral systems in accordance with the National
Electrical Code (NEC), ANSI/NFPA 70, the Canadian Electrical Code, Part I, and Electrical Installations
(Use), NOM-001-SEDE. These devices are intended for use on alternating current (AC)…
1.1
This Standard applies to household cooking ranges having a rating not exceeding 250 V and 21 kW and
designed to be used in accordance with the Rules of the Canadian Electrical Code, Part I.
Note: Throughout this Standard, the word “appliance” is used to refer to the whole group of equipment covered by
this Standard. Where a requirement applies only to one type of equipment, e.g., an…
Formaldehyde emissions standard for composite wood products
1.1
This Standard applies to newly manufactured, unfinished composite wood panels prior to use in
construction, finishing, or installation. The composite wood panel categories covered are
a) hardwood plywood (HWPW) (including composite and veneer core);
b) particleboard (PB);
c) medium density fibreboard (MDF); and
d) thin MDF.
Note: Refer to Clause 3.1 for further clarification.
1.2
This…
Nonincendive electrical equipment for use in Class I and II, Division 2 and Class III, Divisions 1 a...
1.1 Purpose
The purpose of this Standard is to provide minimum requirements for the design, construction, and
marking of electrical equipment or parts of such equipment for use in Class I and Class II, Division 2 and
Class III, Divisions 1 and 2 hazardous (classified) locations.
This equipment, in normal operation, is not capable of causing ignition of the surrounding atmosphere
under the…
1.1 General
This Standard is designed to be used with related occupational or technical standards. It is intended to be referenced by other standards as the primary set of requirements for health and safety management of work in confined spaces.
This Standard is designed for voluntary application in Canadian workplaces. However, the principles established in this Standard are based on best…
ISO 4955:2016 specifies requirements for the grades listed in Table 2, which are usually employed for products for which the resistance to the effects of hot gases and the products of combustion at temperatures in the region above 550°C and/or to long-term mechanical stress is the main requirement.
NOTE 1 Grades mentioned in this International Standard may also be used for corrosion and…
Information technology — Biometrics used with mobile devices
ISO/IEC TR 30125:2016 provides guidance for developing a consistent and secure method of biometric (either alone or supported by non-biometric) personalization and authentication in a mobile environment for systems procured on the open market.
Guidance is provided for
- 1:1 verification or 1:few positive identification;
- biometric sample capture in the mobile environment where…