CSA C22.2 No. 61010-2-034:25
1 Scope and object
IEC 61010-1:2010, Clause 1 and IEC 61010-1:2010/AMD1:2016, Clause 1 apply except as
follows:
1.1.1 Equipment included in scope
Replace the existing text with the following:
This document specifies safety requirements to equipment for measuring insulation resistance
and to equipment for testing electric strength which have an output voltage exceeding 50 V a.c.
or 120 V d.c.
This document also applies to combined measuring equipment which has an insulation
resistance measurement function or an electric strength test measurement function.
This group safety publication focusing on safety essential requirements is primarily intended to
be used as a product safety standard for the products mentioned in the scope, but is also
intended to be used by technical committees in the preparation of publications for products
similar to those mentioned in the scope of this document, in accordance with the principles laid
down in IEC Guide 104 and lSO/lEC Guide 51.
One of the responsibilities of a technical committee is, wherever applicable, to make use of
basic safety publications and/or group safety publications in the preparation of its publications.
This Standard applies to the above-noted equipment that is intended to be installed or used in
accordance with CSA C22.1, Canadian Electrical Code, Part I.
General requirements applicable to the above-noted equipment are provided in CSA C22.2 No. 0.
1 Scope and object
IEC 61010-1:2010, Clause 1 and IEC 61010-1:2010/AMD1:2016, Clause 1 apply except as
follows:
1.1.1 Equipment included in scope
Replace the existing text with the following:
This document specifies safety requirements to equipment for measuring insulation resistance
and to equipment for testing electric strength which have an output voltage exceeding 50 V a.c.
or 120 V d.c.
This document also applies to combined measuring equipment which has an insulation
resistance measurement function or an electric strength test measurement function.
This group safety publication focusing on safety essential requirements is primarily intended to
be used as a product safety standard for the products mentioned in the scope, but is also
intended to be used by technical committees in the preparation of publications for products
similar to those mentioned in the scope of this document, in accordance with the principles laid
down in IEC Guide 104 and lSO/lEC Guide 51.
One of the responsibilities of a technical committee is, wherever applicable, to make use of
basic safety publications and/or group safety publications in the preparation of its publications.
1.1.2 Equipment excluded from scope
Add the following new items to the list:
aa) IEC 61557-8 (Electrical safety in low voltage distribution systems up to 1 000 V a.c. and
1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures –
Part 8: Insulation monitoring devices for IT systems);
bb) IEC 61557-9 (Electrical safety in low voltage distribution systems up to 1 000 V a.c. and
1 500 V d.c. – Equipment for testing, measuring or monitoring of protective measures –
Part 9: Equipment for insulation fault location in IT systems).
1.2.1 Aspects included in scope
Replace item c) of the second paragraph with the following new item c):
c) spread of fire or arc flash from the equipment (see Clause 9);
Replace the third paragraph with the following two new paragraphs:
Requirements for protection against HAZARDS arising from NORMAL USE, REASONABLY
FORESEEABLE MISUSE and ergonomic factors are specified in Clause 16 and Clause 101.
Annex BB provides guidance to equipment manufacturers on HAZARDS that should be
considered for equipment intended for performing tests and measurements on hazardous
conductors, including MAINS conductors and telecommunication network conductors.
OEN:
CSA
Langue:
English
Code(s) de l'ICS:
19.080;
71.040.10
Statut:
Norme
Date de Publication:
2024-12-31
Numéro Standard:
CSA C22.2 No. 61010-2-034:25